• Add-on for NS437
• Plastic housing with stainless steel trim.
• Size: (HxDia.) 30x30mm.
• IP66.

• Floor level lighting which allows for a dazzling range of lighting effects.
• They can be installed in wooden floors, decking, paving, stair skirting, concrete and typically used as marker lights for pathways or entrances, wall washing, uplighting columns or archways and mood lighting in any room in the house including wet rooms and pool areas.
• The fittings stay cool and are safe to walk on.
• 38mm diameter cut out is required for paver fitting.
• Lightsource needs to be located near 2x13A power outlets.
• Separate power feed to colourwheel to allow for continuous colour change or static colour.
• Kit includes: 100W tungsten halogen lightsource, Colour wheel, 4x48mm stainless steel fittings, 4 x fibre optic tails (1m - 4m) and full installation instructions.

Die cast aluminium body. Toughened glass diffuser. Suitable for use in damp or underwater applications to around 1m depth. Must be used with a suitable low voltage transformer (LL162). Dims: (HxWxL) 230mmx215mmx172mm. Lamp: 12V 50W MR16 supplied.

·          IP68 Subemersible 1W 316 stainless steel LED marker light. ROHS - Compliant   

·          Screw threaded body with silicon seals and hexagonal lock-nut allows fitting in bath tubs, showertrays, jacuzzi’s, etc (consult a bathroom specialist for professional installation advice)

·         Mounting surface thickness - Min. 2mm, Max 12mm.  Class 3 Equipment.  Suitable for direct mounting on normally flammable surfaces

·         Submersible to a depth of 2m.   Cut Out Dia. 26 mm.   Overerall Dia. 30mm edge to edge mm.  Glass Dia 20 mm.  Recess Depth  26 mm. 

·         NON-REPLACEABLE LEDs with up to 30,000 hours life makes fittings ideal for inaccessible locations

·         Cool operating temperature. Input Voltage 350mA V

·          Fitted with 1m of cable for connection to a Constant Current LED driver (N.B. to be wired in SERIES)

·          Non-dimmable.  Driver supports up to 9 fittings.

IP68 1w luxeon LED walkover light, Pre-wired with 3m rubberised cable, Submersible to a depth of 2m, 5mm toughened glass, 30 lux at 1m (white LED), Diameter: 60mm, Depth: 39mm, Hole Size required: 50mm.

Viewing angle: 45 degrees, Stainless Steel marine grade 316, 12v sealed for life, Must be wired in series, Requires an LED driver (we recommend LL349 - runs up to 16 fittings). Multi Application - Groundlight - Downlight - Docklight - Decklight - Steplight

For flower beds, outside wall or to light small/medium sized shrubs. For wall mounting or ground spike. Includes spike. Waterproof IP67 rated. 230v Die cast aluminium black body. Borosilicate toughened glass. Mains powered.  Lamp either mains 50w GU10 halogen or 2w 18 LED low energy lamp. Dia. 98mm. Depth 105mm. Complete with 2m of lead.  Rear dia. 75mm if inset to Decking.

For flower beds, outside wall or to small/medium sized shrubs. For wall mounting or ground spike. Includes spike. Waterproof IP67 rated. 230v Die cast aluminium black body. Borosilicate toughened glass. Mains powered.  Built-in BRIGHT 28 LED, 45 degree flood. Dia. 98mm. Depth 105mm. Complete with 2m of lead.

 Stainless Steel Marine grade 316
5mm toughened glass
Sealed for life
Supplied with 3m of 0.5mm rubberised cable
Beam angle 15º
Supplied with Spike
Requires an LED driver LL348
Must be wired in series - Use a LL392 to wire

Head Length       38mm.   Max Height         414mm
Head Diameter    33mm.  Spike Length       370mm

IP65 Waterproof rated.

1-8w LED Driver. For 1w LED products. Will run up to 8 fittings. Supplied with fly leads for rapid connection
Short circuit protection. Overload protection
Input 100v-260v 50-60Hz. Output DC 12v 350mA max.
CE approved. UL approved
L:66mm W:36mm H:22mm

1w LED driver. Luxeon LED power supply for 1w units. Powers from 3 to 16 1w LED units. Direct constant current power supply.  IP20 WATERPROOFING.   MUST BE WIRED IN SERIES.  Short circuit protection. Overload protection. 

This product is not dimmable.

Dimensions: L:111mm, W:48mm, H:29mm

High powered 5w MR16 LED Lamp. Replaces an MR16 Lamp. Low Energy. Long Life. Ideal for Domestic or Commercial Installations.  THERMAL MANAGEMENT: Passive Aluminium Heat sink with fins. BEAM ANGLE: 60 degrees. INPUT POWER: 100-240V AC 50/60Hz. UV or IR: No UV or IR radiation. OPERATING HOURS: Over 20,000 hours. DIMENSIONS: Diameter:49.7mm Length:46mm. DRIVER REQUIRED: LL405/6/7/8 depending on amount of units

These new MR16 intelligent lamps introduce a colour changing scheme to any installation.  Install a single master lamp and up to thirty two slaves.  Point the remote control (LL297) at the master lamp and change the colour of the master and slaves simultaneously.  At the touch of a button enjoy the preset four different colour changing scenes with all of the MR16 lamps changing smoothly through the colour spectrum.  Watch them strobe, flash or fade at the same time!

Adjust the light intensity to four different levels.  Press one of the sixteen different colour buttons and instantly change the mood of your environment.  Built in wiring looms attached to each lamp.  Ideal for bars, restaurants, night clubs, stores, commercial premises – even looks great in domestic homes.

Length 52mm Diameter 50mm.   5w Cree LED.  Colour changing MR16
Beam angle 60º .  4 colour changing programs
2 flash & 2 smooth changes, 16 preset colours
Can be wired with up to 32 Slave Units
Requires an LED driver LL405.   Max: 80m between lamps

Ideal for commercial installations, Night Clubs, Discos, Wine Bars, Parties, Outdoor Lighting, mood creating interior lighting, even childrens bedrooms. Unit has 12 preset colours – red, green, blue, purple, pink, white etc.

On-off button.  Lock-unlock button

4 light intensity buttons.   12 preset colour buttons

This infra-red control comes with 4 pre-set colour changing modes – Flash (changes colour every second); Strobe (every 5 seconds); Fade (quick change through the entire 16 colour spectrum); and Smooth (slow change through the spectrum). It can be used to programme / control any number GU10 colour changing LED lamps.  Requires 2 x AAA batteries

LED Driver designed for use with LL292. Input 100v-240v. Output 12v 20w. Will drive up to 4 of LL292’s Tristar Lamps. Must be wired in parallel. Non dimmable.  IP66 Waterproof rated

Length: 117mm. Width: 33m. Height: 19mm

For flower beds, outside wall or to light small/medium sized shrubs, water features. For wall mounting or ground spike. Includes spike. Waterproof IP67 rated. Die cast aluminium black body. Borosilicate toughened glass. Lamp either low voltage dichroic lamp or LL292 next generation lamp. Dia. 98mm. Depth 105mm. Complete with 2m of lead.

Marine Grade 316 Stainless Steel Spike Light. IP65. Supplied with 2.5mm rubberised cable. Accepts MR16 lamps

Lamp: MR16 12v 50mm (not included). Requires a waterproof IP67 rated transformer, we recommend LL393

Can be used with 3w MR16 LED lamps, single colours (part code LL292) and a remote control (LL297).
Requires an LED driver if LED lamps are used

Diameter: 62mm. Depth: 87mm.  Spike length: 152mm. 90 Degree tilt angle

High efficiency, low power consumption, long life, 240v LED garden lights, utilising the latest generation single super bright LED. C/w. Spike and mounting bracket & 3mtr lead. IP66

White light output, Black housing

Blue light output, Black housing

Green light output, Black housing

Red light output, Black housing

• For outdoor use. Suggested max 25w lamp external and 60w internal
• 8m lightstring.
• 10 @ BC lampholders at 0.75m spacing plus 3m lead.
• Plugged.
• Up to 10 strings can be linked via weatherproof connector.
• Specify Opal lamps in notes, if required